牛卧堂MCU技术交流

标题: M451 要讀取 EADC的溫感Vtemp該怎麼設置 [打印本页]

作者: chu399 时间: 2017-3-19 13:20
标题: M451 要讀取 EADC的溫感Vtemp該怎麼設置
如題，我發現使用 "EADC_ADINT_Trigger" EXAMPLE CODE的設置:

void EADC_ConfigSampleModule(EADC_T *eadc, \
                           uint32_t u32ModuleNum, \
                           uint32_t u32TriggerSrc, \
                           uint32_t u32Channel)

他的描述:  * @param[in] u32ModuleNum Decides the sample module number, valid value are from 0 to 15.
不過Vtemp能用的模組照說明文件是16~18，這樣不就是不能填了。

我照著初始化是動不了，它不會進入中斷。

請問該怎麼設定呢?

作者: yjgna 时间: 2017-4-25 10:40
内部间隙电压和温度传感器
void ADC_Init(void)
{
/* configure AVDD as reference voltage*/
SYS_UnlockReg();
SYS->VREFCTL |= 1<<4;
SYS_LockReg();

   /* Enable EADC module clock */
CLK_EnableModuleClock(EADC_MODULE);

/* EADC clock source is HCLK(72MHz), set divider to 8, ADC clock is 72/8 MHz */
CLK_SetModuleClock(EADC_MODULE, 0, CLK_CLKDIV0_EADC(8));

// /* Configure the GPB9 for ADC analog input pins.  */
// SYS->GPB_MFPH &= ~(SYS_GPB_MFPH_PB9MFP_Msk | SYS_GPB_MFPH_PB10MFP_Msk);
// SYS->GPB_MFPH |= SYS_GPB_MFPH_PB9MFP_EADC_CH6 | SYS_GPB_MFPH_PB10MFP_EADC_CH7;

// /* Disable the GPB9 digital input path to avoid the leakage current. */
// GPIO_DISABLE_DIGITAL_PATH(PB, BIT9);
// GPIO_DISABLE_DIGITAL_PATH(PB, BIT10);

/* Set the ADC internal sampling time, input mode as single-end and enable the A/D converter */
EADC_Open(EADC, EADC_CTL_DIFFEN_SINGLE_END);
EADC_SetInternalSampleTime(EADC, 6);

/* Configure the sample module 0 for analog input channel 6 and software trigger source.*/
// EADC_ConfigSampleModule(EADC, 16, EADC_SOFTWARE_TRIGGER, 16);
// EADC_ConfigSampleModule(EADC, 17, EADC_SOFTWARE_TRIGGER, 17);

SYS->IVSCTL |= SYS_IVSCTL_VTEMPEN_Msk;

EADC_ENABLE_SAMPLE_MODULE_INT(EADC, 0, 1<<16);//Enable ADINT0 sample module 16 interrupt .

EADC_ENABLE_SAMPLE_MODULE_INT(EADC, 1, 1<<17);//Enable ADINT1 sample module 17 interrupt.

/* Clear the A/D ADINT0 interrupt flag for safe */
EADC_CLR_INT_FLAG(EADC, 0x3);

/* Enable the sample module 0 interrupt.  */
EADC_ENABLE_INT(EADC, 0x3);//Enable sample module A/D ADINT0 interrupt.

NVIC_EnableIRQ(ADC00_IRQn);

NVIC_EnableIRQ(ADC01_IRQn);
}

欢迎光临牛卧堂MCU技术交流 (http://www.nuvoton-mcu.com/)